View 3793-5202_148101.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

3MTM Four-Wall Header
www..com
.100" x .100" Latch/Ejector, Straight and Right Angle
3000 Series
* Military (with 3M's 3518 & N3518 polarizing key) and centerbump polarization * Optional ejector latches * Mounting holes for securing header to board * Optional polarizing posts available * High temperature insulator option suitable for "no lead" soldering operations * High temperature option suitable for reflow soldering using "paste in hole" techniques * Solder tail option * See Regulatory Information Appendix for chemical compliance information
Date Modified: May 19, 2009 TS-0772-J Sheet 1 of 4
Physical
Insulator:
Material: Glass Filled Polyester (PBT) Glass Filled Polyester (PCT) - (High Temp Option) Flammability: UL 94V-0 Color: Gray (PBT), Beige (PCT), Black (PCT)
Contact:
Material: Copper Alloy
Plating:
Underplating: Nickel - Overall (See Ordering Information) Wiping Area: 30 " [ 0.76 m ] Gold Solder Tails: Tin Lead or Matte Tin (See Ordering Information)
Marking: 3M Logo, Part Identification Number and Orientation Triangle
Electrical
Current Rating: 2 A (EIA 364-70) Insulation Resistance: >1 x 109 at 500 VDC Withstanding Voltage: 1,000 VRMS at Sea Level
Environmental
Temperature Rating: -55C to +105C Process Rating: 260C - (High Temp PCT insulator verson), single pass, (profile per J-STD-020C)
(PBT insulator version), maximum insulator temperature 191C (solder wave processonly)
Moisture Sensitivity Level: 1 (per J-STD-020C) High Temp. (PCT) versions only
UL File No.: E68080 3
Electronic Solutions Division Interconnect Solutions http://www.3M.com/interconnects/ 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373
3MTM Four-Wall Header
www..com
.100" x .100" Latch/Ejector, Straight and Right Angle
-X0XX Header without Latch Ejector -X2XX Header with Short Ejector/Latch for 3M Sockets without Strain Relief
3000 Series
-X3XX Header with Long Ejector/Latch for 3M Sockets with Strain Relief
.68 [17.3]
.08 [2.0]
.424 .010 [ 10.77 ] .97 Ref [24.6]
.08 [2.0] .573 .010 [ 14.55 ] 1.07 Ref [27.2]
A
.025 .002 Sq Typ [ 0.64 ]
.37 Ref [9.4]
D
.24 [6.1]
.46 Ref [11.7]
.020 0.51
.100 2.54
REF.
.28 7.1
.30 [7.6]
.25 6.4 .13 3.3 2X O .100 [2.54] SEE NOTE #2 .100 2.54 POSITION #1 B REF.
.34 8.6
C L "Y"
Dim. E
F Typ
Section A-A
(Straight)
Position 1 Orientation Triangle
Notch A (See Table 1 & Note1) Notch B (See Table 1) .16 [4.1] Notch C (See Table 1 & Note 1)
.025 .002 Sq Typ [ 0.64 ]
.21 [5.3]
A
B
F Typ
.24 [6.1]
.68 [17.3] .35 [8.9]
.12 [3.0]
C L
"Y"
.30 [7.6]
Dim. E .049 Ref [1.24] .100 Ref [2.54]
.020 [0.51]
2X o .100 [2.54] (See Note 2)
A
C A
B
.197 [5.00] .20 [5.1]
Section B-B
(Right Angle)
C
TS-0772-J Sheet 2 of 4
3
Electronic Solutions Division Interconnect Solutions http://www.3M.com/interconnects/
3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373
3MTM Four-Wall Header
www..com
.100" x .100" Latch/Ejector, Straight and Right Angle
Table 1 Pin Qty
10 14 16 20 24 26 30 34 40 50 60 64
3000 Series
Polarizing Notches
BC BC ABC ABC ABC ABC ABC ABC ABC ABC ABC ABC
3M Part Number
3793 3314 3408 3428 3627 3429 3440 3431 3432 3433 3372 3764
Dimensions A
1.265 (32.13) 1.465 (37.21) 1.565 (39.75) 1.765 (44.83) 1.965 (49.91) 2.065 (52.45) 2.265 (57.53) 2.465 (62.61) 2.765 (70.23) 3.265 (82.93) 3.765 (95.63) 3.965 (100.71)
B
1.104 (28.04) 1.304 (33.12) 1.404 (35.66) 1.604 (40.74) 1.804 (45.82) 1.904 (48.36) 2.104 (53.44) 2.304 (58.52) 2.604 (66.14) 3.104 (78.84) 3.604 (91.54) 3.804 (96.62)
C
0.865 (21.97) 1.065 (27.05) 1.165 (29.59) 1.365 (34.67) 1.565 (39.75) 1.665 (42.29) 1.865 (47.37) 2.065 (52.45) 2.365 (60.07) 2.865 (72.77) 3.365 (85.47) 3.565 (90.55)
D
0.705 (17.91) 0.905 (22.99) 1.005 (25.53) 1.205 (30.61) 1.405 (35.69) 1.505 (38.23) 1.705 (43.31) 1.905 (48.39) 2.205 (56.01) 2.705 (68.71) 3.205 (81.41) 3.405 (86.49)
Tolerance Unless Noted .0 Inch .1 .00
Inch (mm)
.000
.01 .005
[ ] Dimensions for Reference only
Table 2 3M Part Number Suffix
-5XX2 -6XX2 -5XO3 -6XO3
Contact Tail
Solder Tail for .062 (1.57) Thick PC Board Solder Tail for 0.94 (2.39) to .125 (3.18) Thick PC Board
Dim E
.112 .010 (2.84) .155 .010 (3.94)
Pin Cross Section
Dim F .0245 .0005 (0.622) .0245 .0005 (0.622) Diagonals .028 .001 (0.71) .028 .001 (0.71) Corner Radii .0075 Ref (0.191) .0075 Ref (0.191)
Dim G
0.035 .003 (0.89) (See Note 3) 0.035 .003 (0.89)
o.106 or o.116 [2.95] [2.69] .41 (See Note 2) [10.4] Max to Edge of PCB Dim G for Daisy Chain
.300 [7.62] Side to Side Stackability
or o.116 o.106 [2.69] [2.95] (See Note 2) Dim G
"Y"
C L
"Y"
C L
Position 1 .100 .003 [2.54] .232 [5.89] C
.060 [1.52]
Position 1 .100 .003 [2.54] .352 [8.94] B
.029 [0.74]
.100 .003 [2.54]
.100 .003 [2.54]
Recommended Mounting Hole Pattern
(Straight)
Recommended Mounting Hole Pattern
(Right Angle)
Notes: 1. Notches A & C will accomodate 3M Polarizing Keys (3M Part #3518 or #N3518). 2. Mounting hardware: From solder side of pc board use #4-24 thread cutting screw (3M Part # 3341-5) and .116 [2.95] dia mounting hole. For right angle version only, #2-56 bolt and nut (3M Part # 3341-6) with .106 [2.69] dia mounting hole may be used. 3. The recommended PCB hole size for the kinked tail positions on the .112 solder tail connector is .035 .002. See page 4 for kink position details (K2 version). 4. Contact your 3M sales representative for custom requirements.
Ordering Information
X3XXX-XXXXXX
Blank = Std. Temp Gray (PBT) /(Blank or UB Pltg. Req'd.) N = High Temp Beige (PCT) /(Blank or UB Pltg. Req'd.) N = High Temp Black (PCT)/(RB Plating Req'd) 3M Part Number (See Table 1) Pin Configuration 5 = Right Angle Solder Tails 6 = Straight Solder Tails Latch/Ejector System 0 = No Latch/Ejector installed 2 = Short Roll Pin Latch/Ejectors 3 = Long Roll Pin Latch/Ejectors 5 = Short, Snap-In Latch/Ejectors 6 = Long, Snap-In Latch/Ejectors
Plating RB = 30 " [ 0.76 m ] Gold and 200 " [ 5.08 m ] Matte Tin over 100 " [ 2.54 m ] Nickel (App. E1 & C1 Apply) Blank or UB = 30 " (0.76 m ] Gold and 200 " [ 5.08 m ] Tin Lead over 100 " [ 2.54 m ] Nickel (App. E3 & C2 Apply) Tail 02 = for .062 [1.57] thick board 03 = for .094 to .125 [2.39 to 3.18] thick board K2 = kinked for .062 [1.57] thick board
TS-0772-J Sheet 3 of 4
3
Electronic Solutions Division Interconnect Solutions http://www.3M.com/interconnects/
3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373
3MTM Four-Wall Header
www..com
.100" x .100" Latch/Ejector, Straight and Right Angle Part Customization
This spec sheet details our standard offering. 3M has several capabilities that can provide a part tailored to your specific needs. Ask your 3M sales representative or customer service for more details.
.318 [8.08] .100 Dia [2.54]
3000 Series Polarizing Post
3201-4 3201-5 LCP PBT Black Gray
Both snap in and roll pin latches may be ordered separately. Snap in and roll style latches are dimensionally and functionally equivalent. If ordering snap-in or roll pin style latches separately, please use the below chart.
Short Latch Standard Temperature (PBT) High Temperature (PCT) High Temperature (PCT) High Temperature (PPA) High Temperature (PPA) High Temperature (PPA) 3505-2 N3505-2 N3505-2B 3505-30 N3505-30 N3505-30B Long Latch 3505-3 N3505-3 N3505-3B 3505-31 N3505-31 N3505-31B Latch Style Roll Pin Roll Pin Roll Pin Snap-In Snap-In Snap-In Color Gray Beige Black Gray Beige Black
Note: Insert Post into one mounting hardware hole on bottom of header. Set post to protrude .115" [2.92].
2500 & 3000 Series Shrouded Header Total Number of Pins 10 14 16 20 24 26 30 34 36 40 50 60 64 Number of Tails Kinked 4 4 4 4 4 4 4 4 4 4 4 4 4 Positions Kinked 3 3 3 3 3 3 5 7 7 7 7 11 11 4 4 4 4 4 4 6 8 8 8 8 12 12 7 11 13 17 21 23 25 27 27 33 43 49 53 8 12 14 18 22 24 26 28 28 34 44 50 54
* Selective pin removal (ATA or other compatability) * Wire wrap tails styles
Kinked Tail Detail: Kink is located .05" below bottom surface of plastic. External radius of kink toward part centerline.
Mounting Hardware
3341-5 (Installed from bottom of board) 3341-6 (Must be inserted prior to latch on vertical headers)
Polarizing Keys
Dim A N3518 LCP PBT Black Gray .02 .02 3518
.31 [7.9]
.50 [12.7]
Panhead Thread Cutting Screw: #4-24 X 5/16" Type: USA Std BT, Federal BG
Hex Head Bolt, Nut and Washer Bolt - #2-56 X 1/2"
Breakaway Tab .15 [3.8]
.34 Ref [8.6] A
.09 [2.3]
3341-5 & 6 Material - Stainless Steel
Note: #2216 B/A Scotchweld can be used to adhere keys.
TS-0772-J Sheet 4 of 4
3
Electronic Solutions Division Interconnect Solutions http://www.3M.com/interconnects/
3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373
www..com
Regulatory Information Appendix
3M Electronic Solutions Division/Interconnect EUROPE Appendix E1: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product is RoHS Compliant 2005/95/EC. "RoHS Compliant 2005/95/EC" means that the product or part ("Product") does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M's best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M's Regulatory Information Appendix, then 3M's entire liability and Buyer's exclusive remedy will be in accordance with the Warranty stated below.
Appendix E2: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is compliant by exemption under EU Commission Decision 2005/747/EC. "RoHS Compliant 2005/95/EC" means that the product or part ("Product") does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M's best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M's Regulatory Information Appendix, then 3M's entire liability and Buyer's exclusive remedy will be in accordance with the Warranty stated below.
Appendix E3: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as amended by Commission Decision 2005/618/EC. This product contains lead in the solder tail area in excess of the maximum concentration value allowed. Unless otherwise stated by 3M in writing, this information represents 3M's best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M's Regulatory Information Appendix, then 3M's entire liability and Buyer's exclusive remedy will be in accordance with the Warranty stated below.
Appendix E4: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC, as amended by EU Commission Decision 2005/717/EC, as amended by EU Court of Justice Decision 2008/C 116/04 This product contains decaBDE in the insulating material in excess of the maximum concentration allowed for finished products subject to EU RoHS that are placed on the EU market after June 30, 2008. Unless otherwise stated by 3M in writing, this information represents 3M's best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M's Regulatory Information Appendix, then 3M's entire liability and Buyer's exclusive remedy will be in accordance with the Warranty stated below.product Warranty stated below.
RIA-2217A-E
Appendix E5: European Union RoHS
www..com Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC. This product contains lead in excess of the maximum concentration value allowed but is compliant by exemption under Item 6 of the Annex to the Directive. "RoHS Compliant 2005/95/EC" means that the product or part ("Product") does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M's best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M's Regulatory Information Appendix, then 3M's entire liability and Buyer's exclusive remedy will be in accordance with the Warranty stated below.
CHINA Appendix C1: China RoHS
Electronic Industry Standard of the People's Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does not contain any of the following substances in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers (excluding decaBDE); or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M's best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M's Regulatory Information Appendix, then 3M's entire liability and Buyer's exclusive remedy will be in accordance with the Warranty stated below.
Appendix C2: China RoHS
Electronic Industry Standard of the People's Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers (excluding decaBDE); or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M's best knowledge and belief based upon information provided by third party suppliers to 3M. The numerical reference in the symbol above should not be construed as a representation regarding the product's life or an extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with 3M's Regulatory Information Appendix, then 3M's entire liability and Buyer's exclusive remedy will be in accordance with the product Warranty stated below.
RIA-2217A-E
www..com
Appendix C3: China RoHS
Electronic Industry Standard of the People's Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers (excluding decaBDE); or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M's best knowledge and belief based upon information provided by third party suppliers to 3M. The numerical reference in the symbol above should not be construed as a representation regarding the product's life or an extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with 3M's Regulatory Information Appendix, then 3M's entire liability and Buyer's exclusive remedy will be in accordance with the product Warranty stated below.
Important Notice All statements, technical information, and recommendations related to 3M's products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M's current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M. Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of 90 days from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M's option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.
3
3M Electronics Solutions Division
6801 River Place Blvd. Austin, TX 78726-9000 U.S.A. 1-800-225-5373 www.3m.com/interconnects Please recycle. Printed in USA. (c) 3M 2008. All rights reserved. RIA-2217A-E
3M is a trademark of 3M Company.

▲Up To Search▲

Price & Availability of 3793-5202

	To Download 3793-5202 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .